Injection molding machine production process, often need changing mould or repairing mold, leading to shoot mouth parts have the liquid myrrh glue leaks out, liquid myrrh colloid easily penetrate traditional electric heating rings of main body leading to burn, often need to change. Totally-sealing copper furnace mouth can relieve above problems. The product consists mainly of brass tubes to seal heating element, heating element adopts imported high temperature resistance wire (French resistanse wire) and Belgium high-temperature mica plate, lead wire use high-temperature fiber line and outsourcing copper with the qualification method, which lead wire wear-resisting durable. Products of wiring place by copper sockets connected with heating element, with silver fiber welding, make product is completely full seal condition.
Product main characteristics
1, west Germany high-temperature mica plates, has thermostablly, insulation performance good advanced features.
2, euramerican high-temperature hair hotline, have heat faster, even heating, high temperature resistant, etc.
3, high-quality copper has heat conduction fast, heat faster, high temperature resistant, temperature can be 600 ℃ without burned phenomenon etc. Characteristics.
4, full seal to make serious leak adhesive machine shoot mouth has special effects.
5, service life is long, can save a replacement times, improve work effectiveness.
6, technical parameters: environmental temperature - 20 ~ + 60 degrees Celsius, the relative humidity less than 80%.
7, leakage current less than 0.5 MA., the cold insulation resistance Ω > 50M, Grounding resistance < 10 Ω.
Install and use the matters needing attention
1. The electric heating element of loaded position interface should level off without bump phenomenon.
2 the heating elements shall be placed in dry, avoid soaking influence its insulation performance.
3. When installation should check the installation position and electric heating element specifications whether conform to, the use of voltage is consistent.
4. After installation should check within six feet bolts, wiring seat bolts and the wiring bolt whether lock, lest heat bilges cold shrink affect the product's life.
5. This product shall be specified in the voltage, consider using parts night voltage fuctuation larger, we recommend you use stabilizer, lest affect the product's efficiency and longevity.
Products include harting heaters, fever laps, fever, fever sleeve the. Hot runner fever circle (bar), cross section of a variety of styles, such as rectangular cross-section, 4x2mm, 4.2 x2.2 mm. Square 4x4mm, section 3.3 x3.3 mm, 3x3mm, circular cross section, 4mm, such as, 5mm 3mm, 2.5 mm, 2mm, 1.8 mm, 1.6 mm. Hot runner heater product minimum diameter can be amounted to 1.5 mm. At the same time may be installed with J K E type thermocouples, for the production process temperature measurement and control.
注塑机生产过程中,经常需要换模或修模,从而导致射嘴部位有液体状的胶漏出,液体状的胶体很容易渗透传统电热圈的主体从而导致烧毁，经常需要更换。全密封铜炉嘴可解除以上问题。此产品主要由黄铜管来密封发热体，发热体采用进口高温电阻丝（法国电热丝）和比利时耐高温云母板，引出线采用耐高温纤维线以及外包铜质带的出线方式，使引出线耐磨耐用。产品的接线处采用铜卯与发热体连接，用银纤焊焊接，使成品完全处于全密封的状态。
产品主要特点
1、西德耐高温云母板，具有耐高温，绝缘性能良好先进特点。
2、欧美耐高温发热线，具有散热快，发热均匀，耐高温等特点。
3、优质铜材具有导热快、散热快、耐高温、温度可达600℃而无烧毁现象等特点。
4、全密封制作对严重漏胶的注塑机射嘴具有特效。
5、使用寿命长，可节省更换次数，提高工作效力。
6、技术参数：环境温度-20~+60摄氏度，相对湿度小于80%。
7、泄漏电流小于0.5MA.，冷态绝缘电阻>50MΩ；接地电阻<10Ω。
安装和使用注意事项
1. 此电热元件所装位置接触面应平整无凹凸现象.
2. 此电热元件应放置干燥, 避免浸水以影响它的绝缘性能.
3. 安装时应先检查安装位置与电热元件规格是否相符, 使用电压是否一致.
4. 安装以后应再检查内六脚螺栓, 接线座螺栓及接线螺栓是否锁紧, 以免热胀冷缩影响产品的寿命.
5. 本产品应在指定电压下使用, 考虑部分地区夜间电压变动较大, 本公司建议使用稳压器, 以免影响产品的效率和寿命.
产品包括热流道加热器，发热圈，发热条，发热套筒。热流道发热圈（条),截面样式多种化，如长方形截面，4x2mm,4.2x2.2mm.方形截面，4x4mm,3.3x3.3mm,3x3mm,圆形截面如，5mm,4mm,3mm,2.5mm,2mm,1.8mm,1.6mm.热流道加热器产品最小直径可达1.5mm。同时可配带J，K，E型热电偶，用于生产过程中温度测量和控制。 |
Resistanse wire
